您当前的位置：深圳企业网 » 深圳商务服务 »深圳检测服务 »深圳检测认证 » 美国标准 UL94 - 设备和电器部件材料可燃性测试

美国标准 UL94 - 设备和电器部件材料可燃性测试

2025-01-08 20:00 113.110.223.243 1次

发布企业: 深圳市实测通技术服务有限公司商铺
认证: 资质核验：
已通过营业执照认证

入驻顺企：
第
19
年

主体名称：
深圳市实测通技术服务有限公司

组织机构代码：
91440300MADFLKA31U
报价: 请来电询价
测试周期: 5-7天
寄样地址: 深圳宝安
价格费用: 电话详谈
关键词: UL标准，UL测试，UL认证，UL检测，UL质检报告
所在地: 深圳市罗湖区翠竹街道翠宁社区太宁路145号二单元705
联系电话: 17324413130
罗工: 17324413130
检测工程师: 罗卓文 请说明来自顺企网，优惠更多

请卖家联系我

产品详细介绍

Test item 测试名称：

Test For Flammability of Plastic Materials for Parts in Devices andAppliances

设备和器具部件材料的可燃性能试验

Testinfo 测试内容：
Test Items	RelevantStandards
水平燃烧(自撑料)	UL 94:1997, ASTMD635
UL94 HB	IEC 60695-11-10
conditioning	23 ±2°C and 50±5 percentrelative humidity for a minimum of 48 hours

垂直燃烧(自撑料)	ASTM D3801-00/IEC60695-11-10
UL94 V0,V1,V2
conditioning	23 ±2°C and 50±5 percentrelative humidity for a minimum of 48 hours and preconditioned inan air-circulating oven for 168 hours at 70±1°C and then cooled inthe desiccator for at least 4 hours at room temperature, prior totesting.

垂直燃烧(自撑料)	ISO1035
UL94 5VA,5VB	ASTMD5048
conditioning	23 ±2°C and50±5 percent relative humidity for a minimum of 48 hours andpreconditioned in an air-circulating oven for 168 hours at 70±1°Cand then cooled in the desiccator for at least 4 hours at roomtemperature, prior to testing.

水平燃烧(泡沫材料)	ASTMD4986/ISO 3852
UL94 HBF, HF-1,HF-2	IEC60695-11-10
conditioning	23 ±2°C and50±5 percent relative humidity for a minimum of 48 hours andpreconditioned in an air-circulating oven for 168 hours at 70±1°Cand then cooled in the desiccator for at least 4 hours at roomtemperature, prior to testing.

垂直燃烧(软质塑料)	ISO9773
UL94 VTM0, VTM-1,VTM-2	ASTMD4804
conditioning	23 ±2°C and50±5 percent relative humidity for a minimum of 48 hours andpreconditioned in an air-circulating oven for 168 hours at 70±1°Cand then cooled in the desiccator for at least 4 hours at roomtemperature, prior to testing.

Sample Required and Turnaround Time,所需样品及时间
Test Items		TAT (Working Days)
HB		7
12 pieces with the size of 125 ±5 mm long by13.0 ±0.5 mm wide, and provided in the minimum thickness and 3.0(-0.0 +0.2) mm thick. The 3.0 mm thick specimens are not necessaryif the minimum thickness is greater than 3.0 mm, or the maximumthickness is less than 3.0 mm. The maximum thickness is not toexceed 13 mm. The maximum width is not to exceed 13.5 mm, the edgesare to be smooth, and the radius on the corners is not to exceed1.3 mm.
12 pieces with the size of (125 ± 5) × (13 ±0,2) mm Xthickness(需要提供测试的Zui小厚度样品和3毫米厚度样品,若样品Zui小厚度大于3mm,或者Zui大厚度小于3MM,则可以不用提供3mm样品;样品Zui大厚度不超过13mm,Zui大宽度不超过13.5mm,)
V0, V1, V2		14
17 pieces with the size of 125 ±5 mm long by13.0 ±0.5 mm wide, and provided in the minimum and maximumthicknesses. The maximum thickness is not to exceed 13 mm.Specimens in intermediate thicknesses are also to be provided andshall be tested if the results obtained on the minimum or maximumthickness indicate inconsistent test results. Intermediatethicknesses are not to exceed increments of 3.2 mm. Also, the edgesare to be smooth, and the radius on the corners is not to exceed1.3 mm.
17 pieces with the size of (125 ± 5) × (13 ±0,2) mmXthickness(需要提供测试的Zui小厚度样品和Zui大样品厚度；样品Zui大厚度不超过13mm，如果Zui小厚度样品和Zui大厚度样品得出的结果不一致，则还需要提供中间尺寸样品，中间尺寸厚度跨度不超3.2mm)
5VA, 5VB		14
32 pieces with (125 ± 5) × (13± 0.5) mm Xminimum thickness AND 10 pieces 150 ± 5 × 150± 5 mm X minimumthickness
32 pieces with (125 ± 5) × (13± 0.5) mm XZui小厚度和 10 pieces 150 ± 5 × 150± 5 mm XZui小厚度 (Zui大厚度不超过13mm)
HBF, HF-1,HF-2		14
17 pieces 150 ±5 mm long by 50 ±1 mm wide, inthe minimum and maximum thicknesses covering the thickness range tobe considered. Specimens tested by this method are limited to amaximum thickness of 13 mm. Specimens in intermediate thicknessesare also to be provided and shall be tested if the results obtainedon the minimum and/or maximum thickness indicate inconsistent testresults. Intermediate thicknesses are not to exceed increments of 6mm. The maximum width is not to exceed 50 mm. The edges are to besmooth and the radius on the corners is not to exceed 2mm
17 pieces (150± 5) X (50± 1) mm X thickness(Zui小厚度和Zui大厚度都要提供,当Zui大厚度和Zui小厚度的测试结果不一致，则中间的厚度也要提供，间隔不要超过6mm，试样宽度不要超过50mm)
VTM0,VTM-1,VTM-2		14
17 pieces, 200 ±5 mm in length by 50 ±1 mm inwidth, in the minimum and maximum thicknesses that are to be testedcovering the thickness range under consideration. Specimens inintermediate thicknesses are also to be provided and shall betested. if the results obtained on the minimum and/or maximumthicknesses indicated inconsistent test results
17 pieces (200± 5) X (50± 1)mm X thickness(Zui小厚度和Zui大厚度都要提供，这样可以认为测试结果对整个厚度系列有效，但当Zui小厚度和Zui大厚度的测试结果不一致时，中间的厚度也要提供)

Others 其他信息:

1.UL94垂直燃烧，要求前处理70度168小时, 不能申请加急服务

2. SampleReport 报告样本：

所属分类：中国商务服务网 / 检测认证

关于深圳市实测通技术服务有限公司商铺首页 | 更多产品 | 联系方式 | 黄页介绍

法定代表人	罗卓文
主营产品	ROHS认证、CE认证、FCC认证、CB认证、FDA认证、UL认证、CCC认证、GS认证、MIC认证、EK认证、PSE认证、E-MARK 认证等国际安全测试认证
经营范围	一般经营项目是：电子产品、网络通信产品、汽车电子设备及配件的设计、技术开发及销售；智能电子设备、汽车配件、电子产品、五金配件、塑料配件的销售；服装、纺织品、针织品、日用百货销售；元器件、材料、仪器仪表、机电设备、输变电设备、高低压电器元器件及设备的检验、检测以及相关标准和技术的研发及咨询；仪器设备的销售及校准；第一类医疗用品及器械；经营电子商务；国内贸易；货物及技术进出口。(法律、行政法规、国务院决定规定在登记前须经批准的项目除外; 依法须经批准的项目，经相关部门批准后方可开展经营活动），许可经营项目是：无
公司简介	深圳市实测通技术服务有限公司是一家年轻的技术服务型公司，我们拥有富有激情，勇于追逐梦想的团队，我们努力创造好的创业环境不断吸引优秀的行业专家，海归人才，外籍专家及优秀毕业生加入。我们致力于国际化的视野在全球化背景下整合国内外法规，检测与认证资源，建立新型，专业化法规研究，检测与认证服务平台，从IT、AV、家电、灯具、汽车电子、服装纺织等电子消费类产品提供EMC电磁兼容、物理性能、环境可靠性、安全性 ...

公司新闻

游泳圈产品进入欧盟国家市场CE认证怎么办理？
游泳圈用于水中。当你吹气时，游泳圈会有浮力。里面全是气体。把它放在腰上，然后跳起... 2024-06-07
草坪机产品出口欧盟国家CE认证怎么办理？
草坪机，指的是一种割牧草的机械设备和绿化环保设备。它可将牧草和园林中的杂草进行切... 2024-06-07
可折叠沙发床CE认证怎么办理？
可折叠沙发床是可以折叠用来当作床的沙发。可折叠沙发床出口欧盟是需要办理CE认证的... 2024-06-07
手办模型出口欧盟国家市场CE认证怎么办理？
手办模型是指树脂或其他高质量材料经过精细制造打磨或雕刻出来的人物、汽车、飞机、军... 2024-06-07
炒菜机进入欧盟国家CE认证怎么办理？
炒菜机是新一代智能控制智能烹饪设备，设备通常方便，操作简单，无油烟。烹饪机不仅可... 2024-06-07

我们的其他产品