Chemlon® A30
Polyamide 66
Chem Polymer公司
产品说明:
A30 is an unfilled injection moulding grade of nylon 66.It contains a nucleating agent to enable mouldings to be producedwith shorter cycle times
物性信息:
基本信息 | |
---|---|
添加剂 |
|
特性 |
|
加工方法 |
|
物理性能 | 干燥 | 调节后的 | 单位制 | 测试方法 |
---|---|---|---|---|
密度 | 1.14 | -- | g/cm³ | ISO 1183 |
收缩率 1 | 1.1 到 1.7 | -- | % | 内部方法 |
吸水率 (平衡, 23°C, 50% RH) | 2.5 | -- | % | ISO 62 |
机械性能 | 干燥 | 调节后的 | 单位制 | 测试方法 |
---|---|---|---|---|
拉伸模量 | 3100 | 1900 | MPa | ISO 527-2 |
拉伸应力 | 85.0 | 60.0 | MPa | ISO 527-2 |
弯曲模量 | 3000 | 1200 | MPa | ISO 178 |
弯曲应力 | 95.0 | 35.0 | MPa | ISO 178 |
热性能 | 干燥 | 调节后的 | 单位制 | 测试方法 |
---|---|---|---|---|
热变形温度 | ||||
0.45 MPa, 未退火 | 230 | 210 | °C | ISO 75-2/B |
1.8 MPa, 未退火 | 95.0 | 85.0 | °C | ISO 75-2/A |
电气性能 | 干燥 | 调节后的 | 单位制 | 测试方法 |
---|---|---|---|---|
表面电阻率 | 1.0E+14 | 1.0E+11 | ohms | IEC 60093 |
体积电阻率 | 1.0E+16 | 1.0E+15 | ohms·cm | IEC 60093 |
漏电起痕指数 | 600 | -- | V | IEC 60112 |
可燃性 | 干燥 | 调节后的 | 单位制 | 测试方法 |
---|---|---|---|---|
UL 阻燃等级 (1.50 mm) | V-2 | -- | UL 94 | |
灼热丝易燃指数 (1.50 mm) | 750 | -- | °C | IEC 60695-2-12 |
极限氧指数 | 27 | -- | % | ISO 4589-2 |
注射 | 干燥 | 单位制 | |
---|---|---|---|
干燥温度 | 80.0 | °C | |
干燥时间 | 2.0 | hr | |
料筒后部温度 | 270 到 290 | °C | |
料筒中部温度 | 270 到 290 | °C | |
料筒前部温度 | 270 到 290 | °C | |
加工(熔体)温度 | 270 到 290 | °C | |
模具温度 | 60.0 到 80.0 | °C | |
注射速度 | 快速 | ||
Back Pressure | Low | ||
Screw Speed | Moderate |
注射说明 |
---|
No drying is necessary unless the material has been exposedto air for longer than three hours. The appearance of splash markson the surface of mouldings indicates excessive moisture ispresent. |